Search found 57 matches
- Thu Dec 31, 2015 6:16 am
- Forum: Turbo and Engine Management
- Topic: EFI Fuel Tank Options
- Replies: 15
- Views: 45615
Re: EFI Fuel Tank Options
Interesting I also ran a surge tank when I injected my TA27 but have had several issues that I hope to have finally worked out but I used the same set up basically but the fuel returning from the rail would heat up the surge tank and the hot fuel would end up killing the efi pump because of the hot...
- Thu Dec 31, 2015 12:33 am
- Forum: Turbo and Engine Management
- Topic: EFI Fuel Tank Options
- Replies: 15
- Views: 45615
Re: EFI Fuel Tank Options
@Chesmari Thanks for the follow up. I never thought of using a small capacity fuel cell as a surge tank. Did you use the factory lines from the top of the tank to run your lines to the lift pump? I just want to know how you ran your lines to and from the tank. Thanks again I ended up soldering alum...
- Wed Dec 30, 2015 7:13 am
- Forum: Exterior Tech
- Topic: Te51 chin spoiler
- Replies: 3
- Views: 11576
Re: Te51 chin spoiler
VW MKI Golf 2 piece Duckbill maybe?
Ryan
Ryan
- Wed Dec 30, 2015 6:41 am
- Forum: Turbo and Engine Management
- Topic: EFI Fuel Tank Options
- Replies: 15
- Views: 45615
Re: EFI Fuel Tank Options
Finished up my swap this summer on my KE30. I am using the stock tank feeding the pump through the drain plug and returning fuel back to the top of the tank. The pump is failing on me and I am sure it is due to fuel starvation. Has anyone used the stock tank on the KE30 / TE31 for their EFI setup? ...
- Sun Dec 27, 2015 8:58 pm
- Forum: Turbo and Engine Management
- Topic: SR20DET Manifold to T-engines
- Replies: 5
- Views: 13676
Re: SR20DET Manifold to T-engines
As a follow up, saw this post in Toymods: http://www.toymods.org.au/forums/threads/31201-3T-GTE-Tech/page72?highlight=SR20DET Hi Steeko, Since I am currently running an SR20 topmount ebay stainless manifold and previously a factory cast SR20 manifold on my 3T I'll jump in! Port spacing is 'almost' i...
- Sun Dec 27, 2015 7:35 pm
- Forum: Turbo and Engine Management
- Topic: SR20DET Manifold to T-engines
- Replies: 5
- Views: 13676
SR20DET Manifold to T-engines
Has anyone ever considered getting or have done SR20DET Turbo manifold, chop off the flange and weld a T-series exhaust flange onto it? Seems very identical in spacing. Plenty of inexpensive SR20 manifolds out there, just find a shop that TIG welds and have a budget turbo manifold with several of st...
- Sun Dec 27, 2015 7:23 pm
- Forum: Project Gallery
- Topic: 3TGTE37
- Replies: 12
- Views: 30065
Re: 3TGTE37
I will when the time comes to rebuild the engine.....BOBLOOK wrote:Wow Ryan time for an pinned crank
Ryan
- Wed Dec 23, 2015 3:42 pm
- Forum: Chassis and Suspension
- Topic: rear axle swaps
- Replies: 12
- Views: 35020
Re: rear axle swaps
I did this with my TE-37 Ford 8.8 Conversion - 95 & Up Ford Explorer -Spare Passenger side axle to replace driver side axle in order to center the differential. *4L10 - 4.10 Limited Slip *3L73 - 3.73 Limited Slip Explorer 8.8 Measurements: Weight (complete assembly w/ brakes etc.): 174 lb. O.D. ...
- Tue Dec 22, 2015 5:11 am
- Forum: General Parts
- Topic: TE72 and TE28 in Pick your Part
- Replies: 2
- Views: 4877
Re: TE72 and TE28 in Pick your Part
TE28 is gone. TE72 is picked apart....
Ryan
Ryan
- Fri Dec 11, 2015 6:34 am
- Forum: General Parts
- Topic: TE72 and TE28 in Pick your Part
- Replies: 2
- Views: 4877
TE72 and TE28 in Pick your Part
I just visited a pick your part yard located in 1232 N Blinn Ave, Wilmington, CA 90744
There I saw a TE72 and a TE28, seems like more parts are available for picking.
Good luck.
Ryan
There I saw a TE72 and a TE28, seems like more parts are available for picking.
Good luck.
Ryan