Where to wire my Sunpro Tach too?

Moderators: BOBLOOK, AE25, pufito18

Post Reply
Kenny727
Posts: 95
Joined: Sat Apr 11, 2015 10:25 pm

Where to wire my Sunpro Tach too?

Post by Kenny727 »

I have my sunpro tach all wired up except for the wire to read the RPMS..
Now I hear your supposed to use the negative terminal from my coil, but that is not working...

What wire from my module, coil, or distributor should I splice into to get a reading?
If it is the negative coil terminal what else can I try to troubleshoot it?
BOBLOOK
Posts: 2334
Joined: Wed Jun 19, 2013 7:32 pm
Location: Under a bonned in Netherlands.

Re: Where to wire my Sunpro Tach too?

Post by BOBLOOK »

negative terminal from my coil should work any day
The day we learn to think
Kenny727
Posts: 95
Joined: Sat Apr 11, 2015 10:25 pm

Re: Where to wire my Sunpro Tach too?

Post by Kenny727 »

Dang I'm not getting anything. Ill try it again just to be sure, but could it be the tach?
The lights work.. I can set the RPM shift light..
Kenny727
Posts: 95
Joined: Sat Apr 11, 2015 10:25 pm

Re: Where to wire my Sunpro Tach too?

Post by Kenny727 »

Kenny727 wrote:Dang I'm not getting anything. Ill try it again just to be sure, but could it be the tach?
The lights work.. I can set the RPM shift light..
Can I use the wire from behind the Stock tach? IF so what wire would that be?
IS there a fuse the could have been blown inside the tach?
does the gauge of the wire really matter since its just going to the negative?
BOBLOOK
Posts: 2334
Joined: Wed Jun 19, 2013 7:32 pm
Location: Under a bonned in Netherlands.

Re: Where to wire my Sunpro Tach too?

Post by BOBLOOK »

Those tach are universal did you set the correct cyl 4 ?
And the NEG ciol for the reading of the rmp ?
The day we learn to think
Kenny727
Posts: 95
Joined: Sat Apr 11, 2015 10:25 pm

Re: Where to wire my Sunpro Tach too?

Post by Kenny727 »

BOBLOOK wrote:Those tach are universal did you set the correct cyl 4 ?
And the NEG ciol for the reading of the rmp ?
Yes its on 4.. I get no reading in any settting.
And yes it goes directly to the negative side of the coil?
Can I hook it up of the distributor or something?

Now I was short on wire and used a remote amp wire would that be a problem?
BOBLOOK
Posts: 2334
Joined: Wed Jun 19, 2013 7:32 pm
Location: Under a bonned in Netherlands.

Re: Where to wire my Sunpro Tach too?

Post by BOBLOOK »

No the dizzy don't read tach signal

The wire shouldn't be an problem

How did you hooked wires colors ?
The day we learn to think
Kenny727
Posts: 95
Joined: Sat Apr 11, 2015 10:25 pm

Re: Where to wire my Sunpro Tach too?

Post by Kenny727 »

BOBLOOK wrote:No the dizzy don't read tach signal

The wire shouldn't be an problem

How did you hooked wires colors ?

I have it wired:
Black to Ground
Red to Switched power
White to Switched power (Keep the light on)
Green to negative on coil

The - on the coil only has the green wire, and black from the ignitor.

Tomorrow I will use my multi meter
Negative to green wire
positive to red wire
If that shows voltage does it mean its my tach?
Post Reply